Bestsellers

Brand new D16 spark plug, suits many vintage stationary engines including Lister A & B Junior, Lister H, J, K, L, M, N, P, R & Q, Ronaldson & Tippett N Type, Moffat-Virtue V3 and many others.

This 5/16 cast brass wing nut is a sutable replacment for the oil filler flap of all Lister CS engines. It is also suitable for many other Lister stationary engines, or any other use requiring a 5/16 BSW brass wing nut.

Lister CS flywheel gib key suitable for all Lister CS engines with a STD 9/16" wide keyway, sold individually. This gib key may also fit other engines such as Lister L and Lister J engines with the 9/16" wide keyway.
Important Note: These are new keys that will require final size and angle adjustments to suit your flywheel and crankshaft, they are all unique, especially after many years of use and in some cases abuse.

Lister Petter LR, SR, ST, TS, TL, TR & TX high quality non genuine oil filter element suitable for 1, 2 & 3 cylinder engines, equivalent to Lister part number 201-55370.

Fuel filter element suitable for a wide range of Lister Petter engines fitted with the AC Delco AD600 type filter, including the LT, LV, TS, TR, AC, LD, LR, SR & ST range, also found on the later CS 8/1, 16/2 slow speed engines. Equivalent to Lister Patter part number 201-13118.

New replacement old type fuel filter wick for all original Lister diesel engines fitted with this style of fuel filter. This quality aftermarket fuel filter wick complete with nipple and clamp is suitable for use in the original standard cast iron fuel filters found on Lister CS, JP, JK, FR, CE & CD engines.

 Equivalent to Lister part numbers: 023-02288, 23-2288

A quality replacement hardened steel diaphragm for the crankcase breather assembly on all Lister CS engines. Will also fit other Lister engines fitted with this style of crankcase breather, including Lister L, J, A & B models, photos 2, 3 and 4 show this style of breather fitted to other Lister engines.

A pack of 25 x No.4 x 1/4" hammer drive rivets, electroplated for protection against the elements. Will suit most vintage Lister engine nameplates and any other stationary engine ID plates where this size is used.

A very high quality made non asbestos copper laminated gasket for the exhaust flange and inlet joint on all Lister CS & JP diesel engines and the exhaust flange side of early Lister J, K, L & M petrol/paraffin engines.

A new high injector pipe for all Lister CS single cylinder engines, this well-made aftermarket fuel line is used for the high pressure connection between the fuel pump and the injector. Equivalent to Lister P/N’s 8-30-60, 008-30060, 5-1/C73A.

New replacement handle grip made from splinter resistant wood, the handle measures approximately 5" long with a centre hole drilled for clearance on 1/2" diameter bolt. The handle grip comes coated for protection from the elements and ready for use.

Suitable for the Lister CS and most early single cylinder Lister engine starting handles.

A well made quality pepper pot style exhaust silencer suitable for Lister CS, Lister L, Lister J, and Lister B type engines, as well as other similar sized engines that require a silencer with a 1.5" BSP thread fitting.

Full overhaul gasket set suitable for Lister CS 3/1 & 3.5/1 water cooled diesel engines. This high quality non-genuine set comes complete with crankshaft felt seals and 7 stud head gasket. Suitable for 3hp & 3-1/2hp engines with a 3.75' (95.25mm) bore.

A crankshaft main bearing for original Lister CS engines. This is a high quality white metal bush for use with original Lister engines with 2" diameter crankshaft journals.

Sold Individually

New crank case door gasket for all single cylinder British built Lister CS engines, and the early Lister J, K, L & M petrol/paraffin engines. Made from high quality 1.5mm thick oil resistant gasket material as per the originals.

This Lister governor hook is a nice reproduction of the original used on many Lister diesel, petrol and paraffin engines including the Lister A, B, D and CS, would also be a suitable replacement on L and J type engines.

An oil pump rebuild kit for single cylinder Lister CS engines This kit contains the parts needed for overhauling your original brass body Lister CS oil pumps found on 3-1, 3.5-1, 5-1, 6-1 & 8-1 engines.
Note: This kit is not suitable for twin cylinder engines.

A newly made aftermarket 8 litre steel fuel tank to suit all single cylinder Lister CS engines, the kit comes complete with mounting bracket and fuel lines to fit genuine Lister CS engines.

A very nice quality 18mm banjo fuel pipe fitting with hose tail suitable for use on the Lister CS fuel system, allowing you to add a flexible hose from the original cast iron fuel filter to a remote fuel tank.

Full overhaul gasket set suitable for original English built Lister CS 5/1, 6/1 & 8/1 water cooled diesel engines. This high quality non-genuine set comes complete with crankshaft felt seals and 7 stud head gasket. Only suitable for 5hp, 6hp & 8hp engines with a 4.5' (114.3mm) bore.

These are a high quality head gasket suitable for use on genuine Lister CS engines. They will fit the 5/1, 6/1 and 8/1 single cylinder engines and the 10/2, 12/2 and 16/2 twin cylinder engines (2 gaskets required for the twin cylinder engines).

Full set of 4 non-genuine valve springs suitable for all the Lister CS range of diesel engines, these spring sets will also fit the Lister JP’s and CD/CE engines. Included are 2 x inner valve springs equivalent to Lister part numbers 11-3-219 or 012-03219, and 2 x outer valve spring equivalent to Lister part numbers 10-3-129 or 012-03129.

Replacement 5/8" oil seal for Lister CS oil pumps. This seal is a light press fit in top section of the oil pump body and seals around the plunger. Equivalent to Lister part number 008-02178.

Sold Individually

Fuel & Oil Pump packing cord suitable for the Fuel/Oil pumps on all Lister H, J, K, L, M, N, P, R, Q models, P/N 3335. Also suitable for the Lister A & B Junior pump packing P/N 3335. This tried and tested self-lubricated cord is impregnated with fuel resistant lubricant making it ideal for this application.

Sold Per Meter

This good quality "A" section V-Belt Nutlink or Brammer style machine drive belting is suitable for many applications on vintage and workshop machinery. This aftermarket Brammer style link belting is manufactured from a flexible rubberised canvas material. This A section size is approximately ½” or 12-13mm nominal width across the top of the link-belt.

This product is supplied in 1 meter lengths, for longer lengths please select 2, 3, 4 etc when ordering.

Replacement 1/2" oil seal used for sealing around the oil pump tappet in the bottom section of the Lister CS cam shaft cast housing. Equivalent to Lister part number 088-02177.

Sold Individually

Brand new genuine Bosch fuel injector, modern equivalent suitable for Lister CS 5/1, 6/1, 10/2, 12/2 and the CD & CE diesel engines. This high quality injector assembly comes complete with the correct injector nozzle set to 90 ATS and a copper sealing washer. May not be suitable for 3/1, 3.5/1 or some early engines, see below for more details…

A new high quality Lister D copper head gasket, with copper sheeting both sides and copper fire ring. The inner material is made from non asbestos material.

Paper gasket set for twin flywheel Lister A & B Junior engines, not suitable for early single flywheel engines. Does not include the copper valve plug rings or exhaust manifold gasket which are available separately if required.

A new high quality reproduction governor spring suitable for high speed Lister D, DK, A, AK, B & BK petrol & petrol/kerosine engines and CD & CE diesel engines. See suitable speed ranges below. Equivalent to Lister Part Number: J127

A new non genuine cast iron exhaust flange for all Lister CS engines, will also fit Lister J and L models. The flange it has a 1.5" BSP female thread for attaching a muffler directly or by using a 90 degree elbow. This flange can also be use on the inlet port of single cylinder CS engines when the traditional screw in round air filter is used. Includes gasket. A high temp copper laminated gasket is included.

A high quality small stationary engine silencer that would suit a wide range of stationary engines requiring a 1.25" BSP thread exhaust. This muffler will fit engines such as Lister A Juniors and many others.

New non-genuine replacement Lister CS fuel pump tappet and roller assembly c/w adjusting bolt. Equivalent to Lister Part No. 574-10080.