- Lister Diesel Parts
- Lister CS Parts
- Lister JP, JK, JS
- Lister CD & CE
- Lister FR
- Lister LD & SL
- HA, HB & HW
- Lister LR Parts
- Lister SR Parts
- Lister ST & STW
- HR, HRW & HL
- Air, Oil & Fuel Filters
- Gaskets & Seals
- Piston, Rod, Rings & Cylinder
- Bearings & Bushes
- Cylinder Head & Fittings
- Fuel System & Governor
- Exhaust, Air Cleaners & Manifolds
- Starter Motor & Crank Handle
- Lubricating Oil System
- Crankcase, Crankshaft & Camshaft
- Cooling System (Air & Water)
- Studs, Nuts & Bolts
- Electrical & Gauges
- Accessories & Other Parts
- HR2G & HR3G Gas Engine Parts
- Lister LT & LV
- Lister TS, TL & TR
- Air, Oil & Fuel Filters
- Gaskets & Seals
- Piston, Rod, Rings & Cylinder
- Bearings & Bushes
- Fuel System & Governor
- Exhaust, Air Cleaners & Manifolds
- Lubricating Oil System
- Cylinder Head & Fittings
- Crankcase, Crankshaft & Camshaft
- Electrical & Gauges
- Starter Motor & Crank Handles
- Studs, Nuts & Bolts
- Cooling System (Air & Water)
- Accessories & Other Parts
- Lister Petter TX
- LPA & LPW
- JA, JAS, JW & JWS
- CR, CD4/6 & CS4/6
- Vintage Lister Parts
- Petter Engine Parts
- Other Engines
- Piston Rings
- Air, Oil & Fuel Filters
- Fuel Injection Parts
- Gaskets & Gasket Sets
- Silencers & Mufflers
- Books & Manuals
- Transfers & Decals
- Starting Handles
- Nuts, Bolts & Studs
- Oilers & Lubricators
- Magneto & Ignition Parts
- Tools & Supplies
- Cylinder Sleeves
- Belts & Pulleys
- Engine Accessories
Breather & Crank Case
Sort by:Recommended
Lister CS Crankcase Breather Assembly
Out of stockA replacement crankcase breather assembly for Lister engines fitted with this style of crankcase breather, including Lister L, J, A & B models, photos 3, 4 and 5 show examples of this style of breather fitted to other Lister engines.
Lister CS Idler Gear Bolt C/W Nut 008-02029
New replacement Lister CS idler gear bolt, used for bolting the timing idler gear in place while still allowing it to turn. Equivalent to Lister part No. 008-02029
No.4 x 1/4" Hammer Drive Rivets (Electroplated)
A pack of 25 x No.4 x 1/4" hammer drive rivets, electroplated for protection against the elements. Will suit most vintage Lister engine nameplates and any other stationary engine ID plates where this size is used.
Lister CS, L, J, A & B Crankcase Breather Diaphragm
A quality replacement hardened steel diaphragm for the crankcase breather assembly on all Lister CS engines. Will also fit other Lister engines fitted with this style of crankcase breather, including Lister L, J, A & B models, photos 2, 3 and 4 show this style of breather fitted to other Lister engines.
Lister CS Cylinder Studs - 3/4" Whitworth x 17" Long (Set of 4)
A set of 4 Lister CS cylinder/cylinder head studs, these are the 4 main corner studs that screw into the crankcase, each stud is 17" long and threaded at both ends with 3/4” BSW threads. Equivalent to Lister part number 027-00861 x 4.
Lister CS, L & J Idler Gear (Cast Iron) 3185
Lister CS cast iron idler gear, this is a precision machined replacement idler gear for all Lister CS engines. This gear will also replace the P/N 3185 Idler gear on Lister L & J petrol engines made after about 1920. Please select from Genuine (When Available) or Non-Genuine when ordering.
Lister part numbers: 003-00185, 3-185 or 3185.
Lister CS Brass Drain Plug for Crankcase 003-00140
Brass 1” BSP Drain Plug for crankcase on single cylinder Lister CS diesel engines, equivalent to Lister part number 003-00140.
Lister CS, J & L Oil Drain Plug Joint 003-00306
Pair of quality black fibre washers suitable for the oil drain plug and oil pump suction pipe joint for all single cylinder Lister CS engines, these will also fit many of the early petrol/paraffin engines, including the Lister J, K, L, M, N, P, Q & R for both the oil drain plug and suction pipe.
Genuine Lister Pump Hand Lever Swivel Pin 003-00334
A genuine new old stock pump hand lever swivel pin found on single cylinder Lister CS diesels, as well as on Lister J, K, L & M Petrol/Paraffin engines. Lister part number 003-00334.
- New!
No.4 x 1/4" Hammer Drive Rivets (Brass Plated)
A pack of 25 x No.4 x 1/4" hammer drive rivets, brass plated to give an authentic vintage look as well as protection against the elements. Will suit most vintage Lister engine nameplates and any other stationary engine ID plates where this size is used.