Lister A & B Junior

A pack of 25 x No.4 x 1/4" hammer drive rivets, brass plated to give an authentic vintage look as well as protection against the elements. Will suit most vintage Lister engine nameplates and any other stationary engine ID plates where this size is used.

A high quality pair of precision made valve springs for the Lister Junior A & AK type engines, more commonly suitable for 3hp or 3½hp engines. Made from 55CrSi oil tempered and quenched spring steel wire, with a further tempering and shot peening treatment. The ends have been precision ground, and a light coating of anti-rust oil applied for corrosion prevention. Equivalent to Lister part number 2-419 or 002-00419. *Not suitable for all spec’s, see notes.

A high quality pair of precision made valve springs for the Lister H, and the early Junior A and AK type engines, more commonly suitable for 2½hp (A & AK) engines, including single flywheel types. Made from 55CrSi oil tempered and quenched spring steel wire, with a further tempering and shot peening treatment. The ends have been precision ground, and a light coating of anti-rust oil applied for corrosion prevention. Equivalent to Lister part number H56. *Not suitable for all spec’s, see notes.

A high quality pair of precision made valve springs for the Lister J, K and all B & BK Junior engines, including single flywheel types. Made from 55CrSi oil tempered and quenched spring steel wire, with a further tempering and shot peening treatment. The ends have been precision ground, and a light coating of anti-rust oil applied for corrosion prevention. Equivalent to Lister part number 3382 & 003-00382.

5/8" BSW x 2-3/4" long British Whitworth stud. Length of threads (Imperial): TL1 = 0.65" and TL2 = 1.20". Replaces Lister part number 027-00616, 27-616 & S616.

Sold Individually.

New high quality piston ring set to suit the early Lister A Junior engines with a standard 3.75” bore. This is a 3 compression ring set, please check your piston before ordering. All 3 rings in this set have a 7/32” Axial Width.

New high quality piston ring set to suit the early Lister A Junior engines with a standard 3.75” bore. This 3 x compression ring plus 1 x oil ring set was used on engines up to Spec A22 & A62, please check your piston before ordering. All 4 rings in this set have a 7/32” Axial Width.

Lister Junior A, AK, B & BK replacement fuel pump springs equivalent to Lister part number 002-00452 or A452. These springs are made for the later A449 fuel pumps with an external spring under the dust cap, they will not fit the early A214 pumps that had an internal spring under the plunger.

Valve spring carrier suitable for Lister J, K, L, M petrol/paraffin engine and the Lister B & BK junior engines. This replacement spring holder is equivalent to Lister part numbers 3383 & J57, suitable for 7/16” (11mm approx.) valve stems.

Sold Individually.

A replacement bronze camshaft end cover bush suitable for both A & B Type Lister Junior’s, used on twin flywheel versions only. This high quality non genuine part is equivalent to Lister part number A247. Note: You will need to drill the oil lubrication hole after press fitting the bush.

Lister A, AK & B, BK Juniors & H crankcase door gasket, equivalent to Lister part number H87.

Precision made brass 1/4” ball suitable for replacing the often worn or corroded valve balls in vintage Lister A, AK, B & BK Junior fuel pumps and Lister H fuel and oil pumps, equivalent to Lister part number H119.

Sold Individually

Australia made reproduction Gib key cover for the Lister A, AK & B, BK Junior. Only suitable for flywheels with a hub diameter of approximately 75mm to 76mm, please check suitability before purchasing.

Sold Individually

A new high quality reproduction governor spring suitable for low speed Lister D, DK, A, AK, B & BK petrol & petrol/kerosine engines and CD & CE diesel engines. See suitable speed ranges below.

A new high quality reproduction governor spring suitable for high speed Lister D, DK, A, AK, B & BK petrol & petrol/kerosine engines and CD & CE diesel engines. See suitable speed ranges below. Equivalent to Lister Part Number: J127

Brand new D16 spark plug, suits many vintage stationary engines including Lister A & B Junior, Lister H, J, K, L, M, N, P, R & Q, Ronaldson & Tippett N Type, Moffat-Virtue V3 and many others.

Brass spade type spark plug lead terminal for connecting HT lead end to standard type spark plugs with a terminal nut for fixing the cable securely.

Sold Individually

Copper core 7mm HT ignition lead, sold per meter. Taken from 100 meter roll, if you require more than one meter simply add more to your cart and it will be sent as one continuous length where possible.

Sold Per Meter.

Premium quality cotton braided HT ignition cable, 7mm OD with a 1.5mm2 multi strand copper core. Plain black fire retarded cotton cloth braiding covers the PVC insulated core. This high quality product is made in the UK.

Sold Per Meter.

Premium quality cotton braided HT ignition cable, 7mm OD with a 1.5mm2 multi strand copper core. Red with yellow flecks, the fire retarded cotton cloth braiding covers the PVC insulated core. This high quality product is made in the UK.

Sold Per Meter.

Premium quality cotton braided HT ignition cable, 7mm OD with a 1.5mm2 multi strand copper core. Yellow with black flecks, the fire retarded cotton cloth braiding covers the PVC insulated core. This high quality product is made in the UK.

Sold Per Meter.

Premium quality cotton braided HT ignition cable, 7mm OD with a 1.5mm2 multi strand copper core. Plain red fire retarded cotton cloth braiding covers the PVC insulated core. This high quality product is made in the UK.

Sold Per Meter.

Premium quality cotton braided HT ignition cable, 7mm OD with a 1.5mm2 multi strand copper core. Green with red flecks, the fire retarded cotton cloth braiding covers the PVC insulated core. This high quality product is made in the UK.

Sold Per Meter.

A quality cast iron replacement starting handle suitable for the Lister A, AK & B, BK Junior engine range with a 1.5" crankshaft, the starting handle has a ratchet pin that engages in the crank’s keyway. Equivalent to Lister part number A277.

Good quality piston ring set for Lister A petrol engines and AK petrol/kero engines. This ring set is suiatable for the later Juinor engines with a 4” bore, these engines are usually mark as 3hp or 3-1/2hp. The set consists of 3 compression rings and 1 oil scraper ring to suit a standard 4” bore.

High quality piston ring set for Lister B & BK engines. This ring set consists of 3 compression rings and 1 oil scraper ring to suit a standard 4.5” bore.

A high-quality reproduction exhaust silencer for Lister A engines, also known as the Lister Junior. These silencers are a copy of the original Lister type, made to original Lister specification, with internal baffles for effective exhaust note silencing.

A high quality small stationary engine silencer that would suit a wide range of stationary engines requiring a 1.25" BSP thread exhaust. This muffler will fit engines such as Lister A Juniors and many others.

Australian made 1-1/4” BSP exhaust elbow and socket suitable for the Lister Junior A Type and any other engine requiring a 1.25” BSP exhaust bend. These 90 Degree long bends are made from heavy wall pipe, complete with male BSP threads both ends, and the female socket attached to one end allows for easy fitment of a male threaded silencer.

New cast iron exhaust flange suitable for the Lister Junior A type 2.5hp, 3hp and 3.5hp engines. This aftermarket exhaust flange is approximately 25mm thick and has a 1.25" BSP female thread and 2 x mounting holes with 60.3mm centres.

Made from high temperature asbestos free gasket material in the UK.

A quality replacement hardened steel diaphragm for the crankcase breather assembly on all Lister CS engines. Will also fit other Lister engines fitted with this style of crankcase breather, including Lister L, J, A & B models, photos 2, 3 and 4 show this style of breather fitted to other Lister engines.

Decal set for the Lister A & B Hopper Cooled Junior stationary engines, also refered as the "Coffee Pot", 4 transfers are included in this set. These are water slide transfers, instructions for correct use are included. See dimensions below.

Pair of 4” rotation direction arrows for smaller Lister engines including the Lister D, A & B Juniors, and H. This pair of opposing arrows allows for placement on both left and right side flywheels for 2 flywheel models and can be used on both Clockwise and Anti-clockwise by simply switching placement or arrow used.

Sold in Opposing Pairs (As Shown in Photo)

A high-quality reprint Lister Junior instruction Manual with detailed parts list and diagrams for both tank cooled, and hopper cooled engines. Covering the twin flywheel A, AK, B & BK petrol and Paraffin (Vapourising Oil) engines, this 25-page (A4 Size) manual is a valuable reference for anyone owing or restoring one of these engines.

A new inlet or exhaust valve suitable for the Lister Junior A type engines from 2.5HP to 3.5HP. Equivalent to Lister part numbers H55IN & H55EX.

Valves are Sold individually.

New Lister Junior B & BK valves, suitable for inlet and exhaust. These valves are forged, and precision machined from EN52 material as per original Lister specs. Equivalent to Lister part numbers 3381IN (Inlet) and 3381EX (Exhaust).

Valves are Sold individually.

5/16” BSW cast brass wing nut is a suitable replacement for the oil filler flap of all Lister CS engines. It is also suitable for many other Lister stationary engines, or any other use requiring a 5/16” BSW brass wing nut. Lister part number 027-00687, replaces 27-687, S687.

Fuel & Oil Pump packing cord suitable for the Fuel/Oil pumps on all Lister H, J, K, L, M, N, P, R, Q models, P/N 3335. Also suitable for the Lister A & B Junior pump packing P/N 3335. This tried and tested self-lubricated cord is impregnated with fuel resistant lubricant making it ideal for this application.

Sold Per Meter

New brass governor quadrant for the Lister A, AK & B, BK Junior engines. This is an often overlooked and worn part that will greatly affect the governing of these engines. Suits both tank cooled, and hopper cooled Junior engines, original Lister part number A130.

This Lister governor hook is a nice reproduction of the original used on many Lister diesel, petrol and paraffin engines including the Lister A, B, D and CS, would also be a suitable replacement on L and J type engines.

Genuine Lister governor hooks suitable for a wide range of engines in including the CS, A & B Junior, L & J petrol engines, and others. Note that this is the hook only being sold here, there is NO adjusting nut included.

High quality valve cap sealing joints made just like the originals, with a rolled copper fire ring around high temp gasket material. These gaskets fit under the threaded brass plugs that sit over the valves on both tank cooled, and hopper cooled Lister A & B Junior engines.

Not suitable for the early single flywheel models which have a much smaller seal.

Sold in Pairs.

Flywheel gib key suitable for Lister A & B Type Junior engines, equivalent to original Lister part number A175. This 7/16” wide key is approximately 3.75” (96mm) long.

Sold Individually.