Bestsellers

Items: 150 of 261, per page
  • British Standard Whitworth (BSW) nuts available in sizes from 3/16" to 1". Please select required size and quantity then add to cart.

    • $0.15
    • including GST

    Not rated yet
  • 5/16 BSW mild steel studs is lengths commonly used on Lister engines, please select required length from drop down menu. These Whitworth studs could also be used for any other application requiring this size.

    See below for typical applications on Lister engines.

    • $1.10
    • including GST

    Not rated yet
  • 3/8 BSW mild steel studs is lengths commonly used on Lister engines, please select required length from drop down menu. These 3/8 Whitworth studs could also be used for any other application requiring this size.

    See below for typical applications on Lister engines.

    • $1.60
    • including GST

    Not rated yet
  • This 5/16 cast brass wing nut is a sutable replacment for the oil filler flap of all Lister CS engines. It is also suitable for many other Lister stationary engines, or any other use requiring a 5/16 BSW brass wing nut.

    • $2.85
    • including GST

    Score: 5.00 (votes: 1)
  • Brand new D16 spark plug, suits many vintage stationary engines including Lister A & B Junior, Lister L, J, H and many others.

    • $11.95
    • including GST

    Not rated yet
  • 1/2 BSW mild steel studs is lengths commonly used on Lister engines, please select required length from drop down menu. These 1/2 Whitworth studs could also be used for any other application requiring this size.

    See below for typical applications on Lister engines.

    • $1.80
    • including GST

    Not rated yet
  • A pack of 25 new No.4 x 1/4" hammer drive rivets for fixing instruction and identification plates on vintage stationary engines. Will suit most Lister engine nameplates, and may also be suitable for other engines.

    These are steel rivets with an electro plate brass look finish.

    • $5.00
    • including GST

    Not rated yet
    Only 3 left in stock
  • Lister CS flywheel gib key suitable for all Lister CS engines with a STD 9/16" wide keyway, sold individually. This gib key may also fit other engines such as Lister L and Lister J engines with the 9/16" wide keyway.
    Important Note: These are new keys that will require final size and angle adjustments to suit your flywheel and crankshaft, they are all unique, especially after many years of use and in some cases abuse.

    • $11.50
    • including GST

    Not rated yet
  • 7/16 BSW mild steel studs is lengths commonly used on Lister engines, please select required length from drop down menu. These 7/16 Whitworth studs could also be used for any other application requiring this size.

    See below for typical applications on Lister engines.

    • $2.75
    • including GST

    Not rated yet
  • A very high quality made non asbestos copper laminated gasket for the exhaust flange joint on all Lister CS, L, J & JP engines.

    • $5.50
    • including GST

    Not rated yet
  • Lister CS Instruction Manual & Parts List (Reprint)
    • Free

    A high-quality reprint Lister CS instruction Manual with detailed parts list and diagrams. Covering 3.5-1, 6-1, 8-1, 12-2 and 16-2 diesel engines, the 56 page manual is a valuable reference for anyone owing or restoring one of these engines.

    • $20.00
    • including GST

    Not rated yet
  • Pair of valve stem caps suitable for all Lister CS, VA, CD, CE & JP engines.  Hardened to improve wear resistance. Select from either Non-Genuine or Genuine when ordering.

    Lister part number 010-03023, 10-3-23 or 8-1/C23

    • $9.00
    • including GST

    Not rated yet
  • New replacement old type fuel filter wick for all original Lister diesel engines fitted with this style of fuel filter. This quality aftermarket fuel filter wick complete with nipple and clamp is suitable for use in the original standard cast iron fuel filters found on Lister CS, JP, JK, FR, CE & CD engines.

     Equivalent to Lister part numbers: 023-02288, 23-2288

    • $22.00
    • including GST

    Not rated yet
  • High quality new set of replacement piston rings suitable for Lister CS 5-1, 6-1, 10-2 or 12-2 engines with a 4.5" (114.3mm) bore, P/N 574-10970. Available in STD size or + 0.010 Oversize.

    • $33.00
    • including GST

    Not rated yet
  • This Lister governor hook is a nice reproduction of the original used on many Lister diesel, petrol and paraffin engines including the Lister A, B, D and CS, would also be a suitable replacement on L and J type engines.

    • $8.50
    • including GST

    Not rated yet
  • A quality replacement hardened steel diaphragm for the crankcase breather assembly on all Lister CS engines. Will also fit other Lister engines fitted with this style of crankcase breather, including Lister L, J, A & B models, photos 2, 3 and 4 show this style of breather fitted to other Lister engines.

    • $5.50
    • including GST

    Not rated yet
  • A well made quality pepper pot style exhaust silencer suitable for Lister CS, Lister L, Lister J, and Lister B type engines, as well as other similar sized engines that require a silencer with a 1.5" BSP thread fitting.

    • $45.00
    • including GST

    Not rated yet
  • A new exhaust valve guide to suit all Lister CS, JP, JK and JS engine types. equivalent to Lister Petter P/N 010-0383 or 10-3-83. There are 2 options available here, either Genuine (when available) or Non-Genuine.

    • $18.50
    • including GST

    Not rated yet
  • A crankshaft main bearing for original Lister CS engines. This is a high quality white metal bush for use with original Lister engines with 2" diameter crankshaft journals.

    • $48.50
    • including GST

    Score: 5.00 (votes: 1)
  • These are a high quality head gasket suitable for use on genuine Lister CS engines. They will fit the 5/1, 6/1 and 8/1 single cylinder engines and the 10/2, 12/2 and 16/2 twin cylinder engines (2 gaskets required for the twin cylinder engines).

    • $25.00
    • including GST

    Not rated yet
  • A new high injector pipe for all Lister CS single cylinder engines, this well-made aftermarket fuel line is used for the high pressure connection between the fuel pump and the injector. Equivalent to Lister P/N’s 8-30-60, 008-30060, 5-1/C73A.

    • $22.50
    • including GST

    Not rated yet
  • High quality clean white metal conrod bearing shells to replace your original Lister CS & VA big end bearings. These non-genuine coenecting rod bearings are available in standard size for 2.5' crankpin or undersized in 10 thou increment for where your crank has worn and had a regrind.

    Select size when ordering.

    • $31.80
    • including GST

    Not rated yet
  • Lister A & B Junior, HR, HRW, LD, LR, SL, SR, ST & SW Type 1.5" Starting Handle
    • 40% off

    STOCK CLEARANCE SALE! New Improved Version Now Available.
    Cast iron replacement starting handle suitable for most Lister engines requiring a 1.5" crank starting handle. It is known be used on Lister A & B Juniors, HR, HRW, LD, LR, SL, SR, ST and SW.

    • $28.35
    • including GST

    Not rated yet
  • Brand new genuine Bosch fuel injector, modern equivalent suitable for Lister CS 5/1, 6/1, 10/2, 12/2 and the CD & CE diesel engines. This high quality injector assembly comes complete with the correct injector nozzle set to 90 ATS and a copper sealing washer. May not be suitable for 3/1, 3.5/1 or some early engines, see below for more details…

    • $110.00
    • including GST

    Not rated yet
  • High quality new set of replacement piston rings suitable for Lister CS 3-1 & 3.5-1 engines with a 3.75' (95.25mm) standard bore. Equivalent to Lister part number: 574-10960.

    • $31.50
    • including GST

    Score: 5.00 (votes: 1)
  • A new inlet valve guide to suit all Lister CS, VA, JP, JK and JS engine types. equivalent to Lister Petter P/N 010-03039 or 8-1/C39. There are 2 options available here, either Genuine (when available) or Non-Genuine.

    • $16.50
    • including GST

    Not rated yet
  • A very nice quality 18mm banjo fuel pipe fitting with hose tail suitable for use on the Lister CS fuel system, allowing you to add a flexible hose from the original cast iron fuel filter to a remote fuel tank.

    • $8.75
    • including GST

    Not rated yet
  • Bosch/Mico fuel pump (Genuine), this pump is a suitable replacement for original vintage Lister CS engines when used with the adaptor pipe and fittings supplied. This pump is an equivalent to the CAV fuel pumps found on original Lister CS engines.

    • $137.50
    • including GST

    Not rated yet
  • Complete overhaul gasket set for original 3-1 & 3.5-1 Lister CS engines, comes complete with felt seals and 7 stud head gasket. Suitable for 3-1 & 3.5-1 engines with a 3.75' (95.25mm) bore.

    • $55.00
    • including GST

    Not rated yet
  • An oil pump rebuild kit for single cylinder Lister CS engines This kit contains the parts needed for overhauling your original brass body Lister CS oil pumps found on 3-1, 3.5-1, 5-1, 6-1 & 8-1 engines.
    Note: This kit is not suitable for twin cylinder engines.

    • $19.50
    • including GST

    Score: 5.00 (votes: 1)
  • A good quality reproduction exhaust silencer for Lister CS diesel engines and Lister B and L and J type petrel vintage engines. These silencers have internal baffles for effective exhaust note silencing.

    • $65.00
    • including GST

    Not rated yet
  • A good quality 5/8" oil seal for Lister CS oil pumps. This seal is a light press fit in top section of the oil pump body and seals around the plunger.

    Equivalent to Lister part number 008-02178.

    • $3.50
    • including GST

    Not rated yet
  • NSK E15 Bearing for Lucas RS1 & SR Magnetos - Drive End
    • New!

    Replacement bearing for the Lucas RS and SR Magnetos (Drive End), and any other application requiring an E15 Open Type Magneto Ball Bearing. This bearing has a standard radial internal clearance, and the bearings dimensions are 15x35x8.

    • $14.30
    • including GST

    Not rated yet
  • A well made cast iron rocker cover nut for original Lister CS engines. This often missing part comes complete with stud and lock nut.

    • $15.90
    • including GST

    Not rated yet
  • Full set of 4 non-genuine valve springs suitable for all the Lister CS range of diesel engines, these spring sets will also fit the Lister JP’s and CD/CE engines. Included are 2 x inner valve springs equivalent to Lister part numbers 11-3-219 or 012-03219, and 2 x outer valve spring equivalent to Lister part numbers 10-3-129 or 012-03129.

    • $17.50
    • including GST

    Not rated yet
  • Complete overhaul gasket set for original Lister CS 5/1, 6/1 & 8/1 engines with a 4.5' (114.3mm) bore, this non-genuine set comes complete with felt seals and 7 stud head gasket to suit the original English built Lister CS engines. Equivalent to Lister part numbers 657-10390, 657-10391, 657-10392.

    • $55.00
    • including GST

    Not rated yet
  • A high quality head gasket suitable for use on genuine Lister 3-1 and 3.5-1 CS engines or 3HP and 3.5HP respectively.

    • $25.00
    • including GST

    Not rated yet
  • Lister Petrol & Paraffin Engine Manual for H, J, K, L, M, N, P, R, Q & Twins
    • Free

    A high-quality reprint of a 1924 Lister Petrol & Kero Engine Manual with detailed parts lists and diagrams. Covering the H, J, K, L, M, N, P, R, Q & Twins petrol and Paraffin (Vapourising Oil) engines, this 37-page (Plus 5 Fold Out Pages) manual is very detailed and would be a valuable reference for anyone owing or restoring one of these engines. More details below....

    • $29.90
    • including GST

    Not rated yet
  • Full paper gasket comprising of every gasket needed for a complete rebuild of the Lister A & B Junior type engines. Does not include the copper valve plug rings.

    • $19.50
    • including GST

    Not rated yet
    Only 1 left in stock
  • A high quality Australian made crank case door gasket for single cylinder Lister CS engines, as well as Lister L and Lister J type engines. Made from high quality gasket material, the gasket is 1.5mm thick.

    • $4.50
    • including GST

    Not rated yet
    Only 5 left in stock
  • A choice of genuine Lister Petter or a high-quality Non genuine replacement Lister CS inlet and exhaust valve. Each valve is suitable for the inlet and exhaust valve on the CS 5-1, 6-1, 8-1, 10-2, 12-2, 16-2 and VA models. Note: These valves are NOT suitable for Lister CS 3-1 or 3.5-1.

    The valves are sold individually, the price is for one valve.

    • $22.00
    • including GST

    Score: 4.00 (votes: 1)
  • Made in Australia from splinter resistant wood, the handle measures approximately 5" long with a centre hole drilled for clearance on 1/2" diameter bolt. The handles come coated in bee’s wax for protection from the elements and are ready for use.

    Suitable for the Lister CS and most early single cylinder Lister engine starting handles.

    • $12.50
    • including GST

    Not rated yet
  • A high quality small stationary engine silencer that would suit a wide range of stationary engines requiring a 1.25" BSP thread exhaust. This muffler will fit engines such as Lister A Juniors and many others.

    • $35.00
    • including GST

    Not rated yet
    Only 8 left in stock
  • A new non genuine cast iron exhaust flange for all Lister CS engines, will also fit Lister VA, J and L models. The flange it has a 1.5" BSP female thread for attaching a muffler directly or by using a 90 degree elbow. This flange can also be use on the inlet port of single cylinder CS engines when the traditional screw in round air filter is used. Includes gasket. A high temp cooper laminated gasket is included.

    • $22.00
    • including GST

    Not rated yet
  • A new high quality Lister D copper head gasket, with copper sheeting both sides and copper fire ring. The inner material is made from non asbestos material.

    • $25.00
    • including GST

    Not rated yet
  • New replacement Lister CS fuel pump tappet with roller, this is a commonly overlooked part that is often worn on the roller end due to poor lubrication, that cause poor fuel injection.

    • $19.50
    • including GST

    Not rated yet
    Only 1 left in stock
  • A good quality 1/2" oil seal used for sealing around the oil pump tappet in the bottom section of the Lister CS cam shaft cast housing.

    Equivalent to Lister part number 008-02177.

    • $3.50
    • including GST

    Not rated yet
  • Full paper gasket comprising of every paper gasket needed for a complete rebuild of the Lister D type engines. Does not include the copper head gasket which is available to purchase separately in our store.

    • $24.50
    • including GST

    Not rated yet
    Only 10 left in stock
  • A new replacement Lister CS solid water flange, used for connecting pipes to the water inlet and outlet ports on all single cylinder Lister CS engines.

    • $14.50
    • including GST

    Not rated yet
  • A new high quality reproduction Lister D governor spring made as per the original design. This governor spring will also suit many other small vintage stationary engines.

    • $7.50
    • including GST

    Not rated yet
Items: 150 of 261, per page