Lister H to R Range

This 5/16 cast brass wing nut is a sutable replacment for the oil filler flap of all Lister CS engines. It is also suitable for many other Lister stationary engines, or any other use requiring a 5/16 BSW brass wing nut.

A new high quality reproduction governor spring suitable for later Lister J, K, L & M single cylinder petrol & petrol/paraffin engines made from 1922 to end of production. Equivalent to Lister Part Number: 3174

Copper core 7mm HT ignition lead, sold per meter. Taken from 100 meter roll, if you require more than one meter simply add more to your cart and it will be sent as one continuous length where possible.

Sold Per Meter.

A new high quality cast iron crank starting handle suitable for 1.75” crank shafts on many Lister models including J, K, L & M. This high quality reproduction handle will also fit the Southern Cross “Big” P engines and any other engines with a 1.75” (44.45mm) crankshaft that has a keyway for the clutch pin to engage into.

New high quality piston ring set to suit the Lister H 1.5hp & 2hp petrol engines with a standard 3.75” bore. This is a 3 compression ring set, please check your piston before ordering. All 3 rings in this set have a 7/32” Axial Width.

Pair of new gaskets for the Lister L valve plugs found on engines with a blind head. These gaskets are a non asbestos gasket material sandwiched between copper, with a copper fire ring.

New high quality piston ring set to suit the Lister R petrol engines and Lister Q kerosene engines with a 6.875” (174.625mm) standard bore. This is a 4 ring set that includes 4 compression rings with 45° Angle Cut joints.

A new inlet or exhaust valve suitable for the Lister H type engine. Equivalent to Lister part numbers H55IN & H55EX.

Valves are Sold individually.

Premium quality cotton braided HT ignition cable, 7mm OD with a 1.5mm2 multi strand copper core. Plain red fire retarded cotton cloth braiding covers the PVC insulated core. This high quality product is made in the UK.

Sold Per Meter.

Australia made reproduction gib key cover for the Lister J, K, L, M & Twins. Not suitable for all flywheels, please check your hub diameter is approximately 80mm (+1mm -1mm), and the crankshaft is 1.5” diameter before purchasing.

Sold Individually

A new high quality reproduction governor spring suitable for early Lister H, J, K, L & M single cylinder petrol & petrol/paraffin engines. May also be suitable for some N, P, R & Q engines, see notes below. Equivalent to Lister Part Number: J127

Pair of new gaskets for the Lister J valve plugs found on engines with a blind head. These gaskets are a non asbestos gasket material sandwiched between copper, with a copper fire ring.

New high quality piston ring set to suit the Lister N petrol engines and Lister P kerosene engines with a 6.000” (152.4mm) standard bore. This is a 4 ring set that includes 4 compression rings only.

Fuel & Oil Pump packing cord suitable for the Fuel/Oil pumps on all Lister H, J, K, L, M, N, P, R, Q models, P/N 3335. Also suitable for the Lister A & B Junior pump packing P/N 3335. This tried and tested self-lubricated cord is impregnated with fuel resistant lubricant making it ideal for this application.

Sold Per Meter

Premium quality cotton braided HT ignition cable, 7mm OD with a 1.5mm2 multi strand copper core. Green with red flecks, the fire retarded cotton cloth braiding covers the PVC insulated core. This high quality product is made in the UK.

Sold Per Meter.

Lister J, K, L, M stationary engine magneto drive chain, this high-quality Tsubaki (Made in Japan) Simplex roller chain has been made to the correct length for use on Lister engine models J, K, L, M and others.

Precision made brass 1/4” ball suitable for replacing the often worn or corroded valve balls in vintage Lister A, AK, B & BK Junior fuel pumps and Lister H fuel and oil pumps, equivalent to Lister part number H119.

Sold Individually

A very high quality made non asbestos copper laminated gasket for the exhaust flange and inlet joint on all Lister CS & JP diesel engines and the exhaust flange side of early Lister J, K, L & M petrol/paraffin engines.

New high quality piston ring set to suit the Lister L petrol engines and Lister M kerosene engines with a 5.5” bore. This is a 4 ring set, that includes 3 compression rings and 1 oil scraper ring.

Premium quality cotton braided HT ignition cable, 7mm OD with a 1.5mm2 multi strand copper core. Yellow with black flecks, the fire retarded cotton cloth braiding covers the PVC insulated core. This high quality product is made in the UK.

Sold Per Meter.

This Lister governor hook is a nice reproduction of the original used on many Lister diesel, petrol and paraffin engines including the Lister A, B, D and CS, would also be a suitable replacement on L and J type engines.

Valve spring carrier suitable for Lister J, K, L, M petrol/paraffin engine and the Lister B & BK junior engines. This replacement spring holder is equivalent to Lister part numbers 3383 & J57, suitable for 7/16” (11mm approx.) valve stems.

Sold Individually.

New replacement handle grip made from splinter resistant wood, the handle measures approximately 5" long with a centre hole drilled for clearance on 1/2" diameter bolt. The handle grip comes coated for protection from the elements and ready for use.

Suitable for the Lister CS and most early single cylinder Lister engine starting handles.

Lister A, AK & B, BK Juniors & H crankcase door gasket, equivalent to Lister part number H87.

A well made quality pepper pot style exhaust silencer suitable for Lister CS, Lister L, Lister J, and Lister B type engines, as well as other similar sized engines that require a silencer with a 1.5" BSP thread fitting.

New high quality piston ring set to suit the Lister J petrol engines and Lister K kerosene engines with a 4.25” bore. This is a 3 compression ring set, please check your piston before ordering, some engines require a 4 ring set. All 3 rings in this set have a 1/4” Axial Width.

Replacement fuel & oil pump tapered spring suitable for Lister J, K, L, M, N, P, Q, R type engines. These springs have been made to fit both the fuel and the oil side of the pumps. Note: These springs will not suit the early type hollow plungers that require a longer spring, please check that you have solid pluggers before ordering. Sold Individually. Proudly Made in Australia.

Premium quality cotton braided HT ignition cable, 7mm OD with a 1.5mm2 multi strand copper core. Red with yellow flecks, the fire retarded cotton cloth braiding covers the PVC insulated core. This high quality product is made in the UK.

Sold Per Meter.

New crank case door gasket for all single cylinder British built Lister CS engines, and the early Lister J, K, L & M petrol/paraffin engines. Made from high quality 1.5mm thick oil resistant gasket material as per the originals.

New high quality piston ring set to suit the Lister L petrol engines and Lister M kerosene engines with a 5.5” bore. This is a 3 ring set, that includes 3 compression rings only. This set suits early pistons, later pistons had 4 rings, please check your piston before ordering.

Genuine new old stock small end bush suitable for Lister J Type petrol engines and K Type kerosene/paraffin engines made during 1922 or later (Spec 70 onwards). Suit 1” diameter gudgeon pin, approximately 2” (50.8mm) long.

Lister N & P combustion head joint/head gasket suitable for engines with a Ricardo (Detachable) Head. Newly made from high quality non asbestos copper composite materials these head gaskets are equivalent to Lister part number 7533.

A new non genuine cast iron exhaust flange for all Lister CS engines, will also fit Lister J and L models. The flange it has a 1.5" BSP female thread for attaching a muffler directly or by using a 90 degree elbow. This flange can also be use on the inlet port of single cylinder CS engines when the traditional screw in round air filter is used. Includes gasket. A high temp copper laminated gasket is included.

Set of 5 separate transfers that would normally be found on Lister models such as the H, J, K, L, M, N, P, Q and R, it would also not look out of place on the Lister CS, CD, CE range of diesel engines. These are water slide transfers, instructions for correct use are included. See dimensions below.

Premium quality cotton braided HT ignition cable, 7mm OD with a 1.5mm2 multi strand copper core. Plain black fire retarded cotton cloth braiding covers the PVC insulated core. This high quality product is made in the UK.

Sold Per Meter.

A quality Australian made reproduction of the Lister L and Lister J cylinder base gasket, suits both blind and Ricardo heads. Precision made from top quality gasket paper to be an exact copy of the original.

Pair of 6” rotation direction arrows for Lister engines including the Lister CS, J, K, L, M, N, P, R & Q. This pair of opposing arrows allows for placement on both left and right side flywheels for 2 flywheel models and can be used on both Clockwise and Anti-clockwise by simply switching placement.

Sold in Opposing Pairs (As Shown in Photo)