Valve, Rocker & Timing

Lister CS decompression lever complete with bolt.

A well made set of aftermarket push rod to suit the Lister CS and VA engine range, this pair of push rods are a suitable replacement for worn push rods on the Lister CS 3-1, 3.5-1, 5-1, 6-1, 8-1, 10/2, 12/2 & 16/2 engines and they will also fit the VA air cooled engines. Powder coated green for long term protection.

Valve spring carrier and cone/collets suitable for a wide range of vintage Lister diesel engines, including all the CS 3-1, 3.5-1, 5-1, 6-1, 8-1, 10-2, 12-2 & 16-2 range, as well as the VA, CD, CE and JP’s. This aftermarket set includes 6 parts in total, 2 valve spring carriers (010-03130) and 2 (pair) cone/cotters (010-00325).

Sold in pairs as shown in photo.

Pair of Lister CS valve rocker arms with bush, adjusting screws and striking pins, these good quality non-genuine assemblies are ready for use straight out of the box. Suitable for the full Lister CS range including the CS 3-1, 3.5-1, 5-1, 6-1, 8-1, 10-2, 12-2 & 16-2 (2 sets required for twin cylinder engines), the set is also suitable for the Lister VA engines.

Pair of valve stem caps suitable for all Lister CS, VA, CD, CE & JP engines.  Hardened to improve wear resistance. Select from either Non-Genuine or Genuine when ordering.

Lister part number 010-03023, 10-3-23 or 8-1/C23

Full set of 4 non-genuine valve springs suitable for all the Lister CS range of diesel engines, these spring sets will also fit the Lister JP’s and CD/CE engines. Included are 2 x inner valve springs equivalent to Lister part numbers 11-3-219 or 012-03219, and 2 x outer valve spring equivalent to Lister part numbers 10-3-129 or 012-03129.

A choice of genuine Lister Petter or a high-quality Non genuine replacement Lister CS inlet and exhaust valve. Each valve is suitable for the inlet and exhaust valve on the CS 5-1, 6-1, 8-1, 10-2, 12-2, 16-2 and VA models. Note: These valves are NOT suitable for Lister CS 3-1 or 3.5-1.

The valves are sold individually, the price is for one valve.

A choice of genuine Lister Petter or high-quality Non genuine replacement cylinder head valve for the Lister CS 3-1 and 3.5-1 engines, each valve is suitable for the inlet and exhaust. Made from specification EN52 grade steel, these precision ground replacement valves are made to high standards.

The valves are sold individually, the price is for one valve.

Inlet valve guide to suit Lister CS, VA, JP, JK and JS engines. Equivalent to Lister part number 010-03039 or 8-1/C39. Available in Genuine or non-Genuine, select type required when ordering.

A new exhaust valve guide to suit all Lister CS, JP, JK and JS engine types. equivalent to Lister Petter P/N 010-03083 or 10-3-83. There are 2 options available here, either Genuine (when available) or Non-Genuine.

Lister CS complete replacement tappet set, includes 5 pieces, 2 lifter guides, 2 lifters and the threaded flanged insert for the exhaust tappet, this is the piece that works in conjunction with the decompression leaver.

Brand new Lister CS bronze idler gear, this aftermarket gear is a precision machined replacement idler gear made from bronze. Theoretically this bronze idler gear should make the CS somewhat quieter in the gear train than the equivalent cast iron version.

A complete Lister CS Rocker Arm Shaft assembly complete with brass greaser. This rocker shaft will fit all size engines, including 3-1, 3.5-1, 5-1, 6-1 and 8-1, the springs and end caps are spare when used on the 3-1 & 3.5-1 engines, the shaft is the same.

New non-genuine replacement Lister CS fuel pump tappet and roller assembly c/w adjusting bolt. Equivalent to Lister Part No. 574-10080.

A quality replacement bronze bush for original Lister CS valve rocker arms. Sold individually. These new rocker arm/shaft bushes will need to be fit press fit to the rocker arm and reamed if some shrinkage occurs.

Equivalent to original Lister Part Number:  008-24165 or 008-24-165, 8/1C14

New replacement Lister CS idler gear bolt, used for bolting the timing idler gear in place while still allowing it to turn. Equivalent to Lister part No. 008-02029

A replacement rocker block for Lister CS 5-1, 6-1 and 8-1 engines.

Lister CS bronze cam shaft end bush, an often worn part on any well used Lister CS engine, the bush should be replaced when showing any signs of wear. This bush is for the fuel pump/governor end of the camshaft and fits all single cylinder Lister CS engines. The steel bearing for the opposite end of the cam shaft is available separately in our store if required. Please select between Non-genuine and Genuine when ordering.

A new replacement pair of valve rocker adjusting screws and lock nuts Lister CS engines. Suitable for use on all sizes original Lister CS engines and Indian copies.

A replacement 1/8 BSP thread brass greaser and steel extension piece for the Lister CS rocker gear.

Could also be used for any other application requiring a 1/8 BSP thread brass greaser.

A new replacement camshaft end bearing for Lister CS engines. This bearing is for the pressed tin cover end of the cam shaft only, the bronze bush for the governor end can be purchased separately in our store. Suitable for all Lister CS engine sizes.

A good quality replacement cam shaft assembly for single cylinder Lister CS engines. This cam shaft is suitable for use in 3hp, 3.5hp, 5hp, 6hp and 8hp single cylinder Lister CS engines.

A pair of new replacement valve rocker striking pins. These will fit all genuine Lister CS engine sizes.

A new cast iron replacement camshaft end cover for use on all single cylinder original Lister CS engines and Indian copies.

No. 6 taper pin for locating the cam lobes on the Lister CS camshaft, 3 required for single cylinder engines and 7 required for twin cylinders.

No. 6 x 1.75" taper pin for locating the governor gear and end collar on the Lister CS camshaft, 2 required for single cylinder engines and 1 required for twin cylinders.

A new replacement fuel & oil pump cam lobe for the Lister CS camshaft, fits all single cylinder CS engines and No. 1 cylinder on twin cylinder engines. Supplied complete with taper pin.

A new replacement inlet valve cam lobe for the Lister CS camshaft, fits all single cylinder CS engines and both inlets on twin cylinder engines. Supplied complete with taper pin.

A new replacement exhaust valve cam lobe for the Lister CS camshaft, fits all single cylinder CS engines and both exhausts on twin cylinder engines. Supplied complete with taper pin.

Lister CS cast iron idler gear, this is a precision machined replacement idler gear for all Lister CS engines. This gear will also replace the P/N 3185 Idler gear on Lister L & J petrol engines made after about 1920. Please select from Genuine (When Available) or Non-Genuine when ordering.

Lister part numbers: 003-00185, 3-185 or 3185.

A heavy duty cast iron rocker cover for all the Lister CS engine range, including 3-1, 3.5-1, 5-1, 6-1, 8-1, 10-2, 12-2 and 16-6 engines.

A 1/8 BSP thread brass greaser suitable for use on many Lister and other stationary engines including the rocker greaser on Lister D & DK, CS. Original Lister part numbers 27-606, 027-00606, S606.

Could also be used for any other application requiring a 1/8 BSP thread brass greaser.

A good quality replacement rocker assembly complete with brass greaser. This aftermarket set is suitable for 5-1, 6-1, 8-1, 10-2, 12-2 & 16-2 Lister CS engines.

Note: This set is not suitable for the 3-1 & 3.5-1 engines.

A genuine Lister CS valve tappet head, Lister part numbers 026-00379 or 26-379. Used in conjunction with the decompression lever to decompress the exhaust valve for starting.

A genuine Lister CS governor gearwheel suitable for 3-1, 3.5-1, 5-1, 6-1, 8-1, 10-2, 12-2, 16-2 & VA engines. This gear is a replacement for the camshaft gear that hold the governor weights. Lister parts numbers 003-00166, 3-166 or 3166.

A genuine Lister CS camshaft end collar, Lister part number 008-06054.