Nuts, Bolts & Studs

Pair of quality Whitworth studs, 7/16 BSW x 3.5" Long, these studs are commonly used for the Lister CS fuel injector hold down plate, but could easily be used for any other application requiring a Whitworth Stud of this size.

This 5/16 cast brass wing nut is a sutable replacment for the oil filler flap of all Lister CS engines. It is also suitable for many other Lister stationary engines, or any other use requiring a 5/16 BSW brass wing nut.

A pack of 25 x No.4 x 1/4" hammer drive rivets, electroplated for protection against the elements. Will suit most vintage Lister engine nameplates and any other stationary engine ID plates where this size is used.

Set of 3 x 9/16 BSW threaded studs for use on the original 7 stud Lister CS engines to hold the cylinder head in place, these are used in conjunction with the larger four main cylinder studs.

Note: Please select your engine size when ordering, 2 sets are required for twin cylinder engines.

5/16 BSW mild steel studs in lengths commonly used on Lister engines, please select required length from drop down menu. These Whitworth studs could also be used for any other application requiring this size.

See below for typical applications on Lister engines.

3/8 BSW mild steel studs in lengths commonly used on Lister engines, please select required length from drop down menu. These 3/8 Whitworth studs could also be used for any other application requiring this size.

See below for typical applications on Lister engines.

7/16 BSW mild steel studs in lengths commonly used on Lister engines, please select required length from drop down menu. These 7/16 Whitworth studs could also be used for any other application requiring this size. Sizes from 1-1/2" to 5" Long available.

See below for typical applications on Lister engines.

1/2 BSW mild steel studs in lengths commonly used on Lister engines, please select required length from drop down menu. These 1/2 Whitworth studs could also be used for any other application requiring this size.

See below for typical applications on Lister engines.

A set of 4 Lister CS cylinder/cylinder head studs, these are the 4 main corner studs that screw into the crankcase, each stud is 17" long and threaded at both ends with 3/4” BSW threads. Equivalent to Lister part number 027-00861 x 4.

British Standard Whitworth (BSW) nuts available in sizes from 3/16" to 1". Please select required size and quantity then add to cart.

A pair of two new replacement connecting rod end cap bolts, complete with nuts and slit pins. Suit all original Lister CS engine sizes.

9/16 BSW mild steel studs in lengths commonly used on Lister engines, please select required length from drop down menu. These 9/16 Whitworth studs could also be used for any other application requiring this size.

See below for typical applications on Lister engines.

5/8 BSW mild steel studs in lengths commonly used on Lister engines, please select required length from drop down menu. These 5/8 Whitworth studs could also be used for any other application requiring this size.

See below for typical applications on Lister engines.

A pack of 25 x No.4 x 1/4" hammer drive rivets, brass plated to give an authentic vintage look as well as protection against the elements. Will suit most vintage Lister engine nameplates and any other stationary engine ID plates where this size is used.

Flywheel fan cap screw (M8 x 30mm) for Lister Petter TS & TR, this non-Genuine part is equivalent to Lister Petter part number 272-00176.

Sold Individually

Spring Washer used on many Lister Petter models, including TS, TR, LPA, LPW, JA & JW, this non-Genuine part is equivalent to Lister Petter part number 272-00089.

Sold Individually

Lister LD, SL, LR & SR cylinder head nut washer, also used in various other applications on a number of other Lister Petter engines, including but not limited to starter motor nut washers on some models etc. Lister part number 027-00545.

Sold Individually.

Swivel union plug (Banjo Bolt) used for connecting the fuel pipes to CAV fuel filters on Lister Petter HA, HB, ST, HR, TS, TR, LPW, LPW, JA, HW and others. This 1/2″ - 20 UNF steel swivel union plug is equivalent to Lister Petter part number 354-28380. See item 66 in illustration for fitting location and filter type this plug is suitable for.